120mm X 3mm Borosilicate Glass Plate, 3D printer Build Surface, Mini Delta

120mm round 3mm thick borosilicate glass plate. This was designed to work with Monoprice MP Mini Delta, but will also work with any small delta printer than can use a 120mm diameter build area. Borosilicate glass plates are ideally suited for use with 3D printers because they are naturally flat and resistant to thermal shock and warp that can affect other types of glass.

Product Features

  • 120mm round 3mm thick 100% Borosilicate glass plate
  • Low thermal expansion and resistant to thermal shock
  • Very flat surface for 3D printing
  • Great fit on Monoprice MP Mini Delta, slightly over sized to allow for quick alignment

Click Here For More Information

1 Roll 5″ inch WIDE 3D Printing Made In USA PRO Grade Blue Painters Tape Masking Clean Release Easy Removal NO RESIDUE (120MM x 55M 4.7 inch). 3D Printer bed grip deck cover 3D Prints Removal 60 Yd

3D printing enthusiasts will LOVE this tape! Cover your printer bed deck for easy removal of prints and replace tape easily as it wears. 3D printers do not come with good surfaces for easy print removal.

This Blue Painters Tape is Professional Grade multi-use Contractors tape featuring a specially formulated, high tack adhesive. Works for textured, semi-rough, or smooth surfaces and has the tackiness it needs to adhere to your surfaces yet allows for clean removal up to 21 days.

High performance masking tape is for general industrial, construction, and do-it-yourself use. The acrylic adhesive system will not dry out or lose holding power. Works well on drywall, glass, hardwood floors, wood trim, and a variety of surfaces. Most typical use is LATEX paint jobs and window protection mask off.

(REMOVE SLOWLY and carefully from freshly painted surfaces!)

Very Important: Surfaces must be well cleaned, dust free, greaseless, and very dry before application. While the backing of the tape is moisture resistant the adhesive is definitely not. ALL adhesive is pressure & heat sensitive. Make sure you press it firmly after application. Apply at room temperature or above if possible. The dryer and warmer the installation area, the more you run your fingers over it, the better the adhesion (less bleed). REMOVE ASAP! (always pull gently at slight angle AWAY from painted edge) Painters tape is known as semi-permanent removable, it gets stronger every day. The longer you leave it on the more difficulty removing it. Rolled or brushed paint jobs require much sooner removal than sprayed.

Blue Painters Tape is not for everything! May not play well with all types of oil based paints, lacquers, etc. You must be willing to experiment, there are 100’s of kinds of tape for a reason.

Other uses: 3D print bed masking or printer deck covering, Glue or Caulk lines, Over spray protection, Chrome protection when cutting or grinding.

Product Features

  • Premium #1 Grade USA MADE Product – Thicker paper, Stronger adhesive for Contractors & Pros
  • 6 Mil High Tack creped backing, 22.0 steel adhesion, 20 lb tensile strength, 9% elongation
  • UV Resistant for 10 days up to 150 degrees outdoors, 40-125 indoor range for 21 day clean removal
  • 3D Printer bed print surfaces – Strong, flexible, durable, versatile – broad range of applications
  • Dispenser friendly, Pulls off roll VERY quick without tearing, needs LESS pressure to stick down.

Click Here For More Information

IC3D 120mm (4.7″) Wide 22M Long Kapton (Polyimide) Tape

This is a 120mm (4.7″) wide by 22M long roll of Kapton tape (Polyimide). Enough to cover about 50 8×8″ glass sheets. We prefer this size since it’s easier to apply than full width sheets. Printing over heated Kapton taped glass allows for excellent adhesion of melted plastic and gives the bottom of your print a nice smooth finish. After many hours of printing, refresh your printing surface with this stuff. This tape can handle temperatures of up to about 280C. We’ve tested tape from several different manufacturers and chose the best. *** APPLICATION TIP: To minimize the seam from laying to sides down, just spray some lightly soaped water onto the glass and tape. Lay the first side down, slide to position, then squeegee the water out. Respray the second side if necessary, lay down the tape, slide to position to butt up against the first side, slowly squeegee out water. Let dry and trim off the sides. ***

Product Features

  • Provides excellent bed adhesion for 3D printing with ABS and PLA.
  • Enough to tape your 8″x8″ glass sheet about 50 times. Easier application than a single 8″ wide sheet.
  • For best taping results, try spraying lightly soaped water onto the glass and tape. Adjust position and squeegee out water. Let dry.
  • For best adhesion, set bed temp to 110C for ABS and 60C for PLA. Cool down halfway before removing part.
  • Can handle temperatures of up to about 280C.

Detailed Information available on our Homepage…