BIQU SKR V1.3 Control Board 32 Bit Board Smoothieboard with TMC2208 V3.0 3D Printer Parts SKR V1.3 MKS GEN L Ramps 1.4 Board

SKR Motherboard Parameters:
Appearance size: 110*85mm
Mounting size: 102*76mm
Microprocessor: ARM cortex-M3 CPU
Input voltage: DC12V-DC24V 5A-15A
Motor driver: support TMC2208, TMC2130, ST820, LV8729, DRV8825, A4988, can be independently external motor drive
Driver working mode support: TMC2130SPI, TMC2208UART
Motor drive interface: X, Y, Z, E0, E1, five (each has a reextendable interface), Up to 256 subdivisions
Display: 2.8 “TFT, 3.5” TFT, LCD2004, LCD12864

How to Use
The SKR motherboard connects with the computer via the [USB] interface. After the driver is installed, the motherboard can be inserted into the computer to recognize the port for data transmission. Without the driver installed, it is easy for the computer to not recognize the USB port

1. Smoothieware-usb-driver-v1.1 driver installation (Windows systems only) The driver can be obtained from our open-source network
Https://www.dropbox.com/s/ighnj7oa2l0bm5g/smoothieware-usb-driver-v1.1.exe?dl= 0
2. After installing the driver, connect the computer and SKR motherboard with USB cable
Note: When using smoothieware open-source firmware, since only Windows system drivers, the SKR board at this time can only be recognized by the Windows system port! ! !
3. If you are using Marlin2.0 firmware, follow the tutorial to install:
Tutorial:https://www.dropbox.com/s/ppjfflhf3j5yzh2/MarlinV2.0%20SKRV1.1%20instruction.docx?dl=0
Driver:https://www.dropbox.com/s/a0k5idjmf4fn82f/lpc176x_usb_driver.inf?dl=0
If you need more information about this Board please contact us

Package Included
1pcs SKR V1.3 Board
5P TMC2208 V3.0
1pc USB cable

Any Question about this Board please contact with us

Product Features

  • Using 32-bit main frequency 100MHz ARM level Cortex-M3 series LPC1768 main control chip, the performance has been greatly improved
  • Reserved extended port SERVOS of PWM signal to support BL Touch
  • Support Resume Printing While Power Off,Filament Break Detection,Automatic Shutdown After Printing and other functions
  • The SPI working mode of the TMC2130 driver and the UART working mode driven by the TMC2208, which eliminates complex wiring process and can be used by simple unplugging jumper cap
  • SKR V1.3 board has CE Certification to adopt 4-Layer PCB with “Gold Finish” process which capability is more stable and better heat dissipation

Visit The Website For More Information…

BIQU 3D Printer Part SKR Mini V1.1 32bit Control Board Marlin 2.0 Open Source Compatible with Ramps1.4/1.5/1.6 Support A4988/8825/TMC2208/TMC2100 Drivers (DC Connector)

SKR Motherboard Parameters:
Appearance size: 90*70mm
Mounting size: 80*60mm
Microprocessor: ARM Cortex-M3 CPU
Input voltage: DC12V-DC24V 5A-12A
Motor driver: support TMC2208, TMC2130, ST820, LV8729, DRV8825, A4988
Motor drive interface: X, Y, Z, E0, Four(Serial Dual Z-axis), Up to 256 subdivisions
Display: 2.8 “TFT, 3.5” TFT
Temperature Sensor Interface:TH0、TB, two 100K NTC thermistor

Notice:
When the SKR motherboard is electricity , the red light D2 in the lower right corner will light up, indicating that the power supply is normal. The middle of the Board DC SEL is the power selection end
1, when using USB to power the motherboard, short circuit cap should be used to connect +5V and USB Pins
2, when using 12v-24v power supply, short circuit cap shall be used to connect +5V and INT pins

Attention: Can be connected [12v-24v power], [USB] at the same time , the printing process must be connected with a short circuit cap +5V And INT
3,The Board 5V SEL must be connected to INT and +5V two pins before it going to print 4,It must be connected with an external hot bed MOS Extension Module if you need to use with Heatbed, it is very significant that Motherboard can not connect with heat bed directly.

How to use
The SKR motherboard connects with the computer via the [USB] interface. After the driver is installed, the motherboard can be inserted into the computer to recognize the port for data transmission. Without the driver installed, it is easy for the computer to not recognize the USB port

1,The driver can be obtained from our open-source website: https://github.com/bigtreetech, named by “mapleDrv” file
2. After installing the driver, connect the computer and SKR motherboard with USB cable
If you need more information about this Board please contact us

Product Features

  • Using 32bit frequency 72MHz ARM Cortex-M3 series STM32F103RCT6 main Microprocessor, the performance has been greatly improved
  • Support Resume Printing While Power Off,Filament Break Detection,Automatic Shutdown After Printing and other functions
  • SKR Mini V1.1 Board adopt “Gold Finish” process which capability is more stable and better heat dissipation
  • Support 2.8 and 3.5 Inch Touch Screen,2004LCD (but don’t Support 12864 LCD)

Visit The Website For More Information…

BIQU 3D Printer Part SKR V1.3 32bit Control Board Smoothieboard&Marlin Open Source Compatible with Ramps1.4/1.5/1.6 Support A4988/8825/TMC2208/TMC2100 Drivers

Product Description
BIGTREETECH SKR V1.3 motherboard is R&D by Shen Zhen Big Tree Technology CO.,LTD. .The BIGTREETECH SKR V1.3 motherboard not only with a high cost-effective but especially suitable for small and medium-sized 3D printers

How to Work
The SKR motherboard connects with the computer via the [USB] interface. After the driver is installed, the motherboard can be inserted into the computer to recognize the port for data transmission. Without the driver installed, it is easy for the computer to not recognize the USB port

1. Smoothieware-usb-driver-v1.1 driver installation (Windows systems only) The driver can be obtained from our open-source network
Https://www.dropbox.com/s/ighnj7oa2l0bm5g/smoothieware-usb-driver-v1.1.exe?dl= 0
2. After installing the driver, connect the computer and SKR motherboard with USB cable
Note: When using smoothieware open-source firmware, since only Windows system drivers, the SKR board at this time can only be recognized by the Windows system port! ! !
3. If you are using Marlin2.0 firmware, follow the tutorial to install:
Tutorial:https://www.dropbox.com/s/ppjfflhf3j5yzh2/MarlinV2.0%20SKRV1.1%20instruction.docx?dl=0

Product Features

  • Using 32-bit main frequency 100MHz ARM level Cortex-M3 series LPC1768 main control chip, the performance has been greatly improved
  • Reserved extended port SERVOS of PWM signal to support BL Touch
  • Support Resume Printing While Power Off,Filament Break Detection,Automatic Shutdown After Printing and other functions
  • The SPI working mode of the TMC2130 driver and the UART working mode driven by the TMC2208, which eliminates complex wiring process and can be used by simple unplugging jumper cap
  • SKR V1.3 board has CE Certification to adopt 4-Layer PCB with “Gold deposition technology” which capability is more stable and better heat dissipation

Visit The Website For More Information…