KeeYees Professional 3D Printer CNC Kit with Tutorial for Arduino, CNC Shield V3 w/Jumpers + UNO R3 Board + 4Pcs RAMPS 1.4 Mechanical Switch Endstop & DRV8825 GRBL Stepper Motor Driver Heat Sink

CNC Expansion Board:
-GRBL 0.9 compatible
-Runs on 12-36V DC
-4-Axis support: X, Y, Z
-It can drive 4 stepper motors, and each stepper motor only needs 2 IO ports.
That is to say, 6 IO ports can manage 3 stepper motors very well,
which is very convenient to use.

KeeYees UNO R3 Board:
-Microcontroller: ATmega328P
-Chip: ATmega16U2 
-Operating Voltage: 5V
-Input Voltage (recommended):7-12V
-Input Voltage (limit):6-20V
-Flash Memory: 32 KB of which 0.5 KB used by bootloader
-Digital I/O Pins: 14 Digital I/O Pins (6 PWM outputs)
-Analog Input Pins: 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA
-SRAM: 2 KB
-EEPROM: 1 KB
-Clock Speed: 16 MHz
Tips: Find more information about Arduino UNO R3 with the Expansion Board IO Port with our tutorial.

DRV8825 Stepper Motor Driver:
-Applied for driving stepper motors up to 8.2V-45V 2.5A
-4-layer PCB board (better heat dissipation)
-6 different step resolutions:
full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step

Mechanical Switch Endstop:
-Length of Cable: 70 cm
-Red line — VCC (ramps of +)
-Black wire — GND (ramps of -)
-Green Line — SIGNAL (ramps in s)

Package Contents:
1 x CNC Shield Board
1 x KeeYees UNO R3 Board
4 x DRV8825 Stepper Motor Driver with Heat Sink
4 x RAMPS Mechanical Switch Endshop
20 x 2.54mm Black Jumper Caps
1 x 1.5m USB cable for UNO R3 Board

Product Features

  • 【KeeYees UNO R3 Board】 KeeYees UNO R3 Board uses the same ATmega328 and ATMega16U2 as official Uno R3 and 100% compatible with the official version. It comes with free 1.5m USB cable for convenient connection.
  • 【CNC Expansion Board with Free 20pcs Jumpers】This is the latest version of the expansion board, which can be used for engraving machines and 3D printers. It can drive 4 A4988/DRV8825 stepper motors. The jumper caps are necessary for CNC setups. You do not need to purchase this part extra.
  • 【DRV8825 Stepper Motor Driver w/ Heat Sink】DRV8825 is upgrade of A4988! It is a must-have module for 3D printers, CNCs and engraving machines. The 4-layer PCB board has better heat dissipation performance. 
  • 【Mechanical Switch Endstop】It uses a 22AWG wire that can withstand a current of 2A and a voltage of 300V. Better quality than traditional copper wire. It can reach the insulation temperature of 80℃. It is not easy to break, and very convenient to plug and remove.
  • 【Reliable technical support】If you don’t have a CD drive, please visit our website( www.keeyees.com ) to get relevant information or can contact us on Amazon, we will send PDF Document to you.

Click Here If You Need More Detailed Info…

MYSWEETY 39PCS 3D Printer CNC Module Kit, Nema 17 Stepper Motor+CNC Shield Board+UNO R3 Board+RAMPS Mechanical Switch Endstop+DRV8825 GRBL Stepper Motor Driver for Arduino Professional 3D Printer Kit

This is a professional sensor kit for UNO R3. New and upgraded, we provides various components or sensor module, with which you will find it easy for you to complete every experiments or learning. All these are packaged in a portable case, easy to carry and storage.

CNC Shield Board:
Latest CNC Shield Version 3.0 for arduino.
GRBL 0.9 compatible.
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13).
Support 6pcs ends stop for each axis.
Coolant enable.
Compatible with A4988 or DRV8825 stepper driver.
Runs on 12-36V DC.

DRV8825 Stepper Motor Driver:
Stepper motor driver (upgraded from A4988, 2.5 A max
current/phase. It’s not arduino official board but it’s compatible with all arduino software and hardware).

Nema 17 Stepper motor:
Model No.:17HD48002H-22B
Step Angle: 1.8 deg
Holding Torque: 59Ncm(84 oz.in)
Rated Current/phase: 1.7A
Frame Size: 41 x 41mm
Body Length: 47mm
Shaft Diameter: 5mm
Shaft Length: 22mm
Weight: 380g

Mechanical Endstop Connection:
Red line connect VCC (ramps of +)
black wire connect the GND (ramps of -)
Green Line connect SIGNAL (ramps in s)
Tips: Under normal circumstances, the system must be configured to at least three mechanical switches.
Advantage: Easy to install, the more common used styles.
Length of Cable: 70 cm

Package Includes:
1 x CNC Shield Board
1 x UNO R3 Board
1 x 1.5m USB cable for R3 Board
3 x Nema 17 stepper motor 1.7 A (with bracket and screw)
3 x Nema 17 Stepper Motor Mounting Bracket
5 x Mechanical Switch Endstop
3 x 3Pin 70cm Cable
5 x DRV8825 Stepper Motor Driver
5 x Aluminum heatsink w/ 3M tape backing
12x M3 Screws for bracket of stepper motor

Product Features

  • High Quality-Each sensor is made of premium module, so convenient for circuit connection. These components can be used in a wide range of application, simple and the service life is long.
  • NEMA 17 Stepper Motor — Stepper Motor is 84 oz.in (59 Ncm) 47mm Body 1.8 degree with Mounting Bracket Kit DIY 3D Printer CNC Robot with 3pcs Mounting Bracket and 12pcs M3 Screws.
  • CNC Shield V3.0-CNC shield board is suitable for CH340G Shield 3.0 version for Arduino, and compatible for GRBL 0.9.
  • UNO R3 Board-Professional module board for UNO R3, fit well for Arduino, easy to install. A great assortment set for Uno R3 starters to learn with and do not miss it.
  • 3D printer CNC Kit -Multiple types of modules or components in this set, which will meet your different needs of learning or experiment.

Click Here If You Need More Detailed Info…

Kuman Professional 3D printer CNC Kit for arduino, GRBL CNC Shield +UNO R3 Board + RAMPS 1.4 Mechanical Switch Endstop + DRV8825 A4988 GRBL Stepper Motor Driver with heat sink + Nema 17 Stepper Motor

CNC Shield Board:
Latest CNC Shield Version 3.0 for arduino
GRBL 0.9 compatible
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis
Coolant enable
Compatible with A4988 or DRV8825 stepper driver
Runs on 12-36V DC

DRV8825 Stepper Motor Driver:
Stepper motor driver (upgraded from A4988, 2.5 A max current/phase. It’s not arduino official board but it’s compatible with all arduino software and hardware)

Nema 17 Stepper motor Specification:
Model No.:17HD48002H-22B
Step Angle: 1.8 deg.
Holding Torque: 59Ncm(84 oz.in)
Rated Current/phase: 1.7A
Frame Size: 41 x 41mm
Body Length: 47mm
Shaft Diameter: 5mm
Shaft Length: 22mm
Weight: 380g

Mechanical Endstop Connection description:
Red line connect VCC (ramps of +)
black wire connect the GND (ramps of -)
Green Line connect SIGNAL (ramps in s)
Tips: Under normal circumstances, the system must be configured to at least three mechanical switches.
Advantage: Easy to install, the more common used styles
Length of Cable: 70 cm

Package Contents:
1 x CNC Shield Board
1 x Kuman UNO R3 Board
4 x DRV8825 Stepper Motor Driver
4 x Aluminum heatsink w/ 3M tape backing
3 x Nema 17 stepper motor 1.7 A (with bracket and screw)
3 x Nema 17 Stepper Motor Mounting Bracket
12x M3 Screws for bracket of stepper motor
3 x Mechanical Switch Endstop
3 x 3Pin 70cm Cable
1 x 1.5m USB cable for R3 Board

Product Features

  • Latest CH340G CNC Shield expansion board Version 3.0 for Arduino
  • Kuman UNO R3 Board, MCU: ATmega328, USB interface: ATmega16U2 with 1.5m USB Cable
  • 4pcs DRV8825 Stepper Motor Driver with heat sinks
  • 3pcs NEMA-17 Stepper Motor 84 oz.in (59 Ncm) 47mm Body 1.8 degree with mounting Bracket Kit DIY 3D Printer CNC Robot with 3pcs Mounting Bracket and 12 pcs M3 Screws
  • 3pcs Endstop Mechanical Limit Switches for 3D printer RAMPS 1.4 with 3Pin 70cm Cable

Click Here If You Need More Detailed Info…