SainSmart Megatronics Board RepRap Stepper motors Megatronics V2.0 Kit for 3D Printer Arduino

SainSmart Megatronics is based on many famous open-source products including:
Arduino Mega 2560, RAMPS, SD Ramps. Therefor this product is an already proven
design. It combines all major features of these board into a single board
solution for more reliable 3D-printing. Megatronics has a powerful Atmega2560
processor with 256 kB memory, running at 16Mhz. The board can be connected to a
PC using a normal USB cable. It will register as FTDI FT232R device. The board
is compatible with the Arduino Mega 2560 and will therefor be easily programmed
from the Arduino IDE.What’s more. We will offer you a detailed tutorial
including project introduction and their source code.

Specifications:

* Microcontroller: Atmega2560-16AU
* Operating Voltage Electronics:5V
* Operating Voltage High:12-24V (15A heated bed, 7A electronics)
* DC Current per I/O Pin:40mA
* Clock Speed:16Mhz

Features:

* Improved thermo couple support.
* Second thermo couple supported
* Support for 6 stepper drivers
* SMD fuses and MOSFETs
* Extra MOSFET, making 4 regular MOSFETs and one for heated bed.
* Support for the new DRV8825 Pololu stepper drivers
* The board can be powered from 12V1 (12V MAX), by setting a jumper
* The LCD contrast can be adjusted with a trimpot
* 12V1 has a diode to protect against reverse polarization
* The 5V line is protected by a 500mA resettable fuse
* A piezo is included to allow the printer to give feedback with sound
* Each stepper driver slot has a breakout to connect external stepper drivers to
the board.
* Four layer high quality PCB board

Notes´╝ÜPlease download codes via the below link:
https://s3-ap-northeast-1.amazonaws.com/sain-amzn/20/20-029-105/Megatronicsv2TestFirmware.rar

Product Features

  • Improved thermo couple support.
  • Second thermo couple supported
  • Support for 6 stepper drivers
  • SMD fuses and MOSFETs
  • Extra MOSFET, making 4 regular MOSFETs and one for heated bed.

Click Here If You Need More Detailed Info…

SainSmart Megatronics + A4988 + Heatbed Endstop 3D Printer Kit for Reprap Arduino Mega 2560 UNO R3 (With Motor, 12864LCD)

Sainsmart A4988 driver is a carrier board or breakout board for Allegro’s A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection by Pololu; we therefore recommend careful reading of the A4988 datasheet before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2 A output current per coil.

SainSmart Megatronics LCD12864 is 100% compaitble with original design .You can
turn on the light time to do long or short form of the adjustment TRIMM R4100K
from 10 seconds to 2 minutesIf you use a print job at night and parts
department, which means that the new modifications LCD backlight would be
suitable for youLED background light control circuit, a small function of
intelligent controller, With pin short time to decide on all LED turn or
steering 30 seconds

SainSmart Mechanical Endstop perfect for any 3D
printer also for use on CNC machines and other electronic applications.

SainSmart SD Ramps: Breakout board for the microSD socket is not much bigger than your fingernail. Compatible with the SPI interface found on any SD card, this tiny form factor was created for cell phone storage and is perfect for your next 3D printer project! Board comes fully assembled and tested.The bare socket is available.

MK2B is the latest and the best type of heatbed, compatible with all Prusa and Mendel 3d printer variants.

Package List:

1 x Megatronics board

6 x A4988 driver

1 x LCD 12864 With Controller

3 x Mechanical Endstop with cable

1 x Heatbed MK2B

5 x NEMA 17 Stepper Motors

Note: Documentation for your reference:

https://s3-ap-northeast-1.amazonaws.com/sain-amzn/20/20-029-105/Megatronicsv2TestFirmware.rar

Product Features

  • This is the new SainSmart 3D Printer Starter Kit, developed specially for those beginners who are interested in 3D printer.
  • You will have a complete set of Sainsmart’s most common and useful electronic components.
  • You may learn about Sainsmart through using these basic projects.
  • Sainsmart Mega2560 R3 is an ATmega2560 as core microcontroller development board itself has 54 groups digital I / O input / output terminal (14 groups do PWM outputs), 16 sets of simulation than the input side, group 4 UARTs (hardware serial ports), using the 16 MHz crystal oscillator. With the bootloader, download the program directly via USB without having to go through other external writer. Supply part of the optional USB power, or as an external power using the AC-to-DC adapter and battery. Arduino development IDE interface is based on open-source principles, allows you to free download for use in project work, school teaching, motor control, interactive works.
  • Megatronics is based on many famous open-source products including: Arduino Mega 2560, RAMPS, SD Ramps. Therefor this product is an already proven design. It combines all major features of these board into a single board solution for more reliable 3D-printing. Megatronics has a powerful Atmega2560 processor with 256 kB memory, running at 16Mhz. The board can be connected to a PC using a normal USB cable. It will register as FTDI FT232R device. The board is compatible with the Arduino Mega 2560 and will therefor be easily programmed from the Arduino IDE.

Visit The Website For More Information…

SainSmart Megatronics + MK2B + A4988 LCD12864 Controller Heatbed Endstop Kit for Reprap 3D Printer Arduino Mega 2560 UNO R3

* Megatronics is based on many famous open-source products including: Arduino
Mega 2560, RAMPS, SD Ramps. Therefor this product is an already proven design.
It combines all major features of these board into a single board solution for
more reliable 3D-printing. Megatronics has a powerful Atmega2560 processor with
256 kB memory, running at 16Mhz. The board can be connected to a PC using a
normal USB cable. It will register as FTDI FT232R device. The board is
compatible with the Arduino Mega 2560 and will therefor be easily programmed
from the Arduino IDE.

* Sainsmart LCD 12864 with Controller contains a SD-Card reader, an rotary
encoder and a 128 Character x 64 Line LCD display. You can easy connect it to
your megatronics board using the “smart adapter” included. After connecting this
panel to your megatronics you don’t need your pc any more, the Smart Controller
supplies power for your SD card. Further more all actions like calibration, axes
movements can be done by just using the rotary encoder on the Smart Controller.
Print your 3D designs without PC, just with a g-code design stored on the SD
card.

* SainSmart Mechanical Endstop perfect for any 3D printer (Including Prusa
Mendel i2, Prusa i3, MendelMax, Rostock etc…) also for use on CNC machines and
other electronic applications.

* This product is a carrier board or breakout board for Allegro’s A4988 DMOS
Microstepping Driver with Translator and Overcurrent Protection by Pololu; we
therefore recommend careful reading of the A4988 datasheet before using this
product. This stepper motor driver lets you control one bipolar stepper motor at
up to 2 A output current per coil.

* MK2B is the latest and the best type of heatbed money can buy as of today.
100% compatible with all Prusa and Mendel 3d printer variants.

Product Features

  • This is the new SainSmart 3D Printer Starter Kit, developed specially for those beginners who are interested in 3D printer.
  • You will have a complete set of Sainsmart’s most common and useful electronic components.
  • Codes and documentation will be provided for you to download: https://s3-ap-northeast-1.amazonaws.com/sain-amzn/20/20-029-105/Megatronicsv2TestFirmware.rar
  • You may learn about Sainsmart through using these basic projects.
  • 1xMegatronics board, 6xSainsmart A4988 driver,1xLCD 12864 With Controller, 3xMechanical Endstop with cable, 1xHeatbed MK2a

Click Here If You Need More Detailed Info…