Tag: Sensor

Creality 3D Upgraded BLTouch V1 Auto Bed Leveling Sensor Kit Accessories for Creality 3D Ender 3/ Ender 3 Pro/Ender 5/CR -10/CR-10S/CR-10S4/S5/CR20/20Pro

NOTE：
The circuit wiring of CR-10 S4, CR-10 S5, CR 20, CR20 Pro are different from the manual, while Ender 3,Ender 3 Pro,Ender 5, CR-10 are same as the manual.
1. Use USB cable to connect CR-10 S4, CR-10 S5, CR 20, CR20 Pro with computer to flash the firmware, the ISP connector and ISP pinboard are not needed.
2. No need to plug the pinboard A to mainboard of CR-10 S4, CR-10 S5, CR 20, CR20 Pro, just insert the connectors into the mainboard D11 pins and unplug Z limit switch then insert the connectors into the Z port.

Features:
An auto leveling sensor for 3D Printer based on open-source.
Simple, high-quality, smart and precise.
Used for 3D Printer for CR-10/for CR-10SPRO/ENDER-3,

Item type:Auto Press Bed Leveling Kit
Material: Plastic
Color: As pictures.

Packing includes:
1 set of Leveling Kit

Notes:
1. Due to the different monitor and light effect, the actual color of the item might be slightly different from the color showed on the pictures. Thank you!
2. Please allow 1-3cm measuring deviation due to manual measurement.

Note:
If the BL touch doesn’t work well. you can reference the website: www.antclabs.com/wiring3

Product Features

  • Application: Suitable for Ender-3 / Ender-3s / Ender-3 Pro /Ender 5 /CR-10 / CR-10S/ CR 10S4/ CR 10S5/ CR-20 / CR-20 Pro and so on 3D Printer(Note: Please flash the firmware first, with ISP cable to connetct computer and printer while CR 10Scan be connected directly to computer by USB)
  • Easy to Use: This auto bed leveling sensor make it easier to levelling the hot bed, which can precisely measure the tilt of Bed surface. Bed leveling is not a problem anymore.
  • Intelligence, self – check and alarm. Function of auto leveling is adopted to make it easier to use and to increase the success rate of shaping.
  • Firmware:Please move to the Creality Official Website to download: https://creality3d.cn/products/
  • Packing includes: 1 set of auto bed Leveling Kit (as image shows). If you have any question about this product, please feel free to contact us!

Detailed Information available on our Homepage…

TRONXY New Upgraded 3D Printer XY-2 PRO Fast Assembly Quick Installation Auto Leveling Continuation Print Power Filament Sensor Full Color Touch Screen 255X255 X 260

Print size:255*255*260mm 
                      Power Input:110V/220V 
Power Output:360W
Positioning accuracy:X/Y0.0125mm, Z0.02mm 
  Print speed:20-100mm/s 
            Connection method : USB interface.TF card
Nozzle size :0.2mm, 0.3mm, 0.4mm optional 
     Hot bed temperature: max 120 C
Nozzle temperature:max275°C
Materials support :PLA.ABS.HIPS.WOOD.PC.PVC  

environmental temperature 8-40°C
print thickness：0.1mm-0.4mm optional 
            Environmental humidity:20-80%
Machine materials: Aluminium and sheet metal
Slicing software :TRONXY slice 
Machine weight : 8.5kg   
                                        File format    STL.OBJ.DAE.AMF.G-Code
Packing weight : 11kg   
                                        Operate software: Repetier-Host. Cura

Packing size :495*460*220mm   
                        Operate system :WinXP/Win7/MacOS
Machine size: 460*450*510mm     
                        Power failure resume print :included
Display :3.5 inches full color touch screen 
      Auto level : included
Filament run-out detector: included
Certificates：CE  FCC

Product Features

  • Single Cable Design—-Complete wiring installation in one step. Compared with the complicated messy cable, the single cable design is more safer and convenient.
  • Three Important Features——-1)Automatic Leveling, help avoid a lot leveling troubles.2)Resume Printing after Power Off.3)Filament run out detection, When the filament runs out or disconnected, the printer will automatically suspended to ensure the model can be smoothly printed
  • 3.5inch Full Color Touch Screen—New experience, HD display, simple operation, convenient and quick.
  • Three Steps Installation—-Quickly install the TRONXY XY-2 PRO printer in just 3 steps, suitable for beginners
  • After-Sales Service—–[email protected] [email protected] TRONXY will offer lifetime technical support and give satisfactory response to you. For the jet lag or Chinese New Year holidays etc, we may not be able to respond to you in time during those special periods, but we can guarantee that we will reply to it within 24 hours under normal conditions. Please wait patiently, don’t rush to give us a bad review. Your trust will give us biggest motivation.

Click Here For More Information

FYSETC 3D Printer Ender 3 Upgrade Parts, Auto Bed Leveling Sensor Heat Bed Auto-Level Probe Module Accessories Pin 27 Board for Creality Ender 3 CR-10 Filament Sensor BLTouch, Black

FYSETC is a professional supplier of 3D Printers related accessories products. Include Popular Printer CR-10, Ender 3, Prusa i3, Makerbot, Anet A8, Duplicator i3, Tevo Tarantula, Maker Select V2 etc. It has a professional R&D team and high quality after-sales service to ensure that you can purchase at a reliable price. If you need more, please feel free to email or Q&A us, we and our engineers are very happy to assist you.

Please Notes:
Q: My printer is Ender 3, When I put it in the port where the ribbon cable was and install the bltouch and the ribbon cable, when I try to put the case for the control board back on, the fan hits the ribbon cable plug on the pin27 board and cannot close.
A1: If you meet this issues, please don’t worry, only need to print a new top cover, we have shown the file in our pictures. please reference.

Package includes:
1 x pin 27 connector

Product Features

  • 2019 Ender 3 Upgrade parts,compatibility with creality Ender 3, CR-10, CR-10 Mini, but not work with the Ender 2, the ender 2 uses pin 29.
  • How to installtion: With this adapter, no wires need to be cut!! Simply connect this between your board and your cable, attach the 3 bltouch wires and upgrade your firmware.
  • Ensure you connect BLTouch’s 3 pins per the labeling on the board.
  • If you need more other information, please reference the thingiverse (search keywords: ender 3 auto bed leveling sensor) and youtube video(keywords:ender 3 bltouch with sd card).
  • After Sales Guarantee: each one defective item can have the free replace or refund, need more help please feel free to contact us, we and our engineers will try our best to assist you.

Visit The Website For More Information…