UEETEK 3 Pcs DC 12V Fan for 3D Printer,Turbine Blower Radiator Fan,Excellent for Cooling Heat Sink on Hot End,3D Printer Accessory

Description

This item is a 3D printer cooling blowing fan, which is made of high quality PBT. It is excellent for cooling heatsinks on hot ends, prints, or other cooling needs, bearing is high precision, long life and low noise.

Features

– Brand: UEETEK.
– Color: Black.
– Pitch: 54.26mm.
– Power: 1.8W.
– Type: blowers, humidifiers.
– Bearings: Oil-bearing.
– Wind: 5.9CFM.
– Operation Voltage: DC 12V.
– Current Rating: 0.15A.
– Revolution: 2200 ± 10% R.P.M.
– Wind Speed: 2.8M / S.
– Noise: 18dBA.
– Excellent for cooling heatsinks on hot ends, prints, or other cooling needs.
– Bearing is high precision, long life and low noise.
– Service life: the working environment temperature of 40℃ (30000 hours).

Package Including
3 * UEETEK DC 12V 3D Printer Blowing Fan for Cooling Heatsinks (Black)

Product Features

  • Color: Black. Pitch: 54.26mm. Power: 1.8W.Type: blowers, humidifiers.
  • Bearings: Oil-bearing. Wind: 5.9CFM. Operation Voltage: DC 12V.
  • Current Rating: 0.15A. Revolution: 2200 ± 10% R.P.M.
  • Wind Speed: 2.8M / S. Noise: 18dBA.
  • Excellent for cooling heatsinks on hot ends, prints, or other cooling needs.

Detailed Information available on our Homepage…

HESAI DRV8825 Stepstick Stepper Motor Driver Module + Heat Sink for RepRad 3D Printer RAMPS 1.4 Controller Replace A4988 (Pack of 5 pcs)

Description:

The DRV8825 stepper motor driver carrier board TI DRV8825 micro bipolar stepper motor drive is a breakthrough. The module has a pinout and interface with our A4988 stepper motor driver carrier is almost the same, so it can be used as a better performance of the pull-down menu board replacement in many applications. DRV8825 features an adjustable current limit, overcurrent and overtemperature protection, six micro-resolution (down 1/32-step). It uses 8.2 – 45 V, can provide up to about 1.5 per phase no heat sink or forced air flow (rated up to 2.2 per volume sufficient additional cooling).

Feature:

A simple steps and direction control interface

Six different steps resolutions: full step, half step, 1/4-step1/8-step1/16-step, 1/32-step

CAN interface directly with 3.3 V and 5 V systems

Over-temperature thermal shutdown, overcurrent shutdown, undervoltage lockout

Short to ground short circuit load protection

4 Layer 2 oz copper PCB, in order to improve heat dissipation

Exposed solder ground below the bottom of the driver IC on the printed circuit board pad

Module size, pin and interface matching A4988 stepper motor driver operators in many ways

Adjustable current control lets you set a potentiometer, which lets you use the stepper motor\’s rated voltage or more, in order to achieve a higher rate of maximum output current step

Intelligent chopping control automatically selects the correct current decay mode (fast decay or slow decay)

Maximum 45 V supply voltage

Built-in voltage regulator (the need for any external logic supply voltage)

Package List:

5x DRV8825 Stepper Motor Driver

5x Heatsink

1x Screwdriver

Product Features

  • This DRV8825 Stepper Motor Driver Module is upgrade of A4988
  • Simple step and direction control interface
  • 4-layer, 2 oz copper PCB for improved heat dissipation
  • Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
  • Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates

Visit The Website For More Information…

HESAI 3D Printer Controller Kit for Arduino Mega 2560 R3 Board + RAMPS 1.4 Control Panel + LCD 12864 Motherboard Display + 5pcs DRV8825 Stepstick Stepper Motor Driver Module + Heat Sink

MEGA 2560 R3 Board

The Mega is 100% compatible with Arduino and most shields designed for the Arduino

The chip is Atmega2560-16au and Atmega16u2, same with the official version.

Improved and expert version: 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible both with the board that use the AVR, which operate with 5V and with the Due that operate with 3.3V. The second one is a not connected pin, that is reserved for future purposes.

Stronger RESET circuit.

It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started.

RAPMS 1.4 Controller

Fully assembled & tested, no soldering required

Designed to fit the entire electronics needed for a RepRap in one small package for low cost.

Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.

A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.

Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

LCD 12864

Using a large screen 12864LCD.

With a SD card base on back, put slicing file into the SD card and select the file on the LCD, then can be printing.

Product comes encoder parameter adjustment can be achieved, and the file selection print.

Plug and play on the RAMPS, but need to modify the firmware to support.

Package List:

1x MEGA 2560 R3 Board

1x RAMPS 1.4 Controller

1x LCD 12864

5x DRV8825 Driver

5x Heat Sink

1x Screwdriver

Product Features

  • Fully assembled & tested, no soldering required
  • Designed to fit the entire electronics needed for a RepRap in one small package for low cost.
  • Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.
  • A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
  • Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

Click Here If You Need More Detailed Info…