2x 0.2mm Nozzle Print Head +2x 0.2mm Nozzle Cleaning Kit
2x 0.3mm Nozzle Print Head +2x 0.3mm Nozzle Cleaning Kit
4x 0.4mm Nozzle Print Head +4x 0.4mm Nozzle Cleaning Kit
2x 0.5mm Nozzle Print Head +2x 0.5mm Nozzle Cleaning Kit
- 10pcs Extruder Brass Nozzle Print Head for MK8 Makerbot Reprap 3D Printers
- Extruder Brass Nozzle Print Head:Material – copper (brass);Color – Golden
- Input Diameter: 1.75mm Output Diameter: 0.2 mm 0.3mm 0.4mm 0.5mm
- The drill bits will clear your printer nozzles very well and print better
- Note:Don’t use the drill to clean until the nozzle is heated to above 200 degrees
Click Here For More Information
Basic requirements: 12V 30A 360W
Rated voltage range: 110-220VAC
Input voltage range: 110-220V
Input frequency range: 47 ~ 63Hz
Input voltage protection: 115 ~ 150% intermittent mode
Input voltage recovery: automatic recovery
Impact current: ≤1%
Machine efficiency: ≤ 0.5%
Output voltage range: 12V ± 0.5%
Output current: 30A
Ripple and noise: ≤100 mVp-p
Rise time: ≤50ms
Voltage regulation rate: ≤0.5%
Load regulation: ≤1%
Output over-current protection: current sag type
Output short circuit protection: IGBT
Output over-voltage protection: soft-start protection
Insulation resistance: > 50MΩ
High-quality materials, heat-resistant, dust-proof and moistureproof, flame-retardant, built-in cooling fan, safe and reliable, can guarantee better cooling effect, the service life of up to 20,000 hours
* This product is not waterproof, please be careful when you use it.
* This Power Supply is only suitable for indoor use, non-detachable power shell.
* Don’t place other items in the product range of 5 cm, to ensure the powersupply with good thermal environment and safety.
* Carefully verify the power link is correct rigorously, power lines reversed before use it. Don’t touch the case during the power is working.
* Don’t place other items in the product range of 5cm, in the range of 50cm within the outlet Do not place other flammable items.
* Do not short-circuit output if no output, please use off one minute re-energized.
* Professional installation of qualified electrician is highly recommended.
* If the power supply is defective, please contact us at first.
1 * 12V 30A Power Supply
- Dimensions: 21.5 * 11.5 * 5.0 cm /8.46*4.53*1.97 inch (L*W*H)
- Operating temperature: -10 ℃ ~ +50 ℃, 20% ~ 95% RH (no condensation)
- Storage temperature: -20 ℃ ~ +85 ℃, 20% ~ 95% RH (no condensation)
- Temperature coefficient: 0.02 ~ 0.05% / ℃
- Cooling method: fan cooling
Click Here For More Information
Temperature resistance: HT-NTC100K (no need to change the firmware, directly replace the old thermistor)
Feeding type: remote feeding
Heater power: 50W
Type of pipe: straight through throat
Heater voltage: 12V
Line length: 1M
Product weight: just the sensor 36g, with 1M heater 65g
Note: This product is with the high temperature line but the hotend itself is through throat, with Teflon inside, so the temperature can not exceed 260 degrees, otherwise it will cause Teflon melt and get clogged!
Hotend+Fan stents+Cooling fan+1M Heater&Thermistor
- Compared to the ordinary aluminum in the market, it adopts high-purity aviation aluminum, is more durable.
- Great texture. Hotend surface is with oxidation scrub, and the black paint texture makes it more upscale.
- Processed by CNC machine, pay attention to the details of each process to ensure the processing accuracy, and every part is highly joined.
- Improved installation makes the hotend can be dismantled in case of clogged, solve the problem, and extend service life. At the same time, it can be modularly replaced and assembled.
- Straight through throat, the filament can be direct access to the nozzle, makes the feeding more smoothly to reduce clogging (the maximum temperature should not be over 260 °. )
Visit The Website For More Information…