BIQU 3D Printer Part Tango V1.0 Control Board Upgraded Rumba Controller Board Support Multi-Color Printing for 3D Printer

Introduction
Electronic part is the brain of a 3D printer, and all movements are controlled by electronic parts. The Tango1.0 baord is R&D for 3D Printer,which is Based on AVR Processor ATMEGA2560 controller board.It support three different color filament, You can use a personal computer with a USB cable to control the 3D printer

Product Parameter
product name:BIGTREETECH-Tango V1.0 Dimension:150mm*75mm
Net weight:99g (No driver)
Power output: 12-24V
Support motor number: six
Support motor driver: A4988、DRV8825、TMC2100
Controller screen: LCD2004、LCD12864 and other screen
Compiled file:Arduino IDE
Firmware:Marlin
Controller software:Printrun、Repetier-Host

Product instruction
1. There are six stepper motor and five temperature sensor input interfaces;
2. Power input is 12-24V, the rated voltage of the hot bed is same as the input voltage of the power supply, the voltage of the hot bed will be 12v if the voltage of power supply is 12v,and the voltage of the hot bed will be 24v if the voltage of power supply is 24v.
3.PWM DC output (heating rods, fans, etc.); 6 outputs (1 large current, 3 medium currents, 2 small currents), driven by high performance, low on-resistance MOS transistors, LED as an indicator for each output.
4. Totally support for JTAG operation

Package List:
1xTango 3D Controller
1X USB Cable

Product Features

  • Integrated design, installed easily. Compared with other 3D printer control board(such as RAMPS, etc.), the Tango V1.0 support more motor drivers, Reduce some straight plug-in part, which improve the connectivity and stability
  • LCD expansion interface,support LCD screen and SD expansion interface, it can achieve offline printing
  • Using ATMEGA2560 as the main control chip, with high-performance USB to UART chip CP2102,it is compatible to all related RAMPS firmware
  • Five ADC interfaces for temperature measurement, three nozzle temperature measurement, one hot bed temperature measurement, and one ambient temperature measurement
  • Six-way PWM: Three control nozzle heating, one control the heating of the hot bed, two control fan rotation; Six-way limit switch; Xmin/Xmax, Ymin/Ymax, Zmin/Zmax can be connected to sensors such as mechanical switches, optical switches, and proximity switches

Visit The Website For More Information…

SODIAL 3D printer accessories motherboard control board MKS GEN-L V1.0 compatible ramps open source marlin

* SODIAL is a registered trademark. ONLY Authorized seller of SODIAL can sell under SODIAL listings.Our products will enhance your experience to unparalleled inspiration.
SODIAL(R) 3D printer accessories motherboard control board MKS GEN-L V1.0 compatible ramps open source marlin
Use CH340 serial port chip, more easily install the drive than 16U2.8. Run Marlin firmware, the configuration is completely same as Ramps 1.4, and available to directly replace the Ramps 1.4.Support Ramps 1.4, 2004LCD,12864LCD, TFT28 and TFT32.Available to input 24V, the heated bed current can be reduced to 1/4 at the same system power which effectively resolves the problem that the MOSFET of heated bed heats.
X axis, Y axis and Z axis with different color terminal controls the stepper motors and endstops, which is convenient to wire.Plug the stepper drivers according to the different color terminals which decreases the probability of reverse and prevents the controller board damage.
Name: MKS-Gen-L V1.0 Controller Board
net weight: 0.1KG
colour: black+yellow+red
Material: metal
Package Contents:
1pcs * MKS-Gen-L V1.0 Controller Board
1pcs * USB line(Random color, don’t accept the specified color. )
Only the above package content, other products are not included.
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.

Product Features

  • Aiming at the problems exist on the open sourced controller board such as Ramps 1.4, the developers in Makerbase specially optimize and develop a new product, MKS Gen_L, which provides more flexible choices for users.
  • 2560 and Ramps 1.4 are integrated in the board, which avoids the complicated connectors.Support a variety of stepper drivers such as A4988, DRV8825, TMC2100 and LV8729, available to change the stepper drivers and motors as users like.
  • Reserve external driver signal, available to connect external high-current driver to drive the 57 and 86 stepper motors.
  • Use high-quality MOSFET, better cooling and more stable.Use specific power chip, support 12V-24V power input, and resolve the problems of chip heating and power shortage.Stable and reliable filter circuit greatly reduces interference and avoids crashes as possible in the process of printing.

Detailed Information available on our Homepage…

Turnigy Mini Fabrikator 3D Printer v1.0 Spare Parts ?�? Metal Set 1

Turnigy Mini Fabrikator 3D Printer v1.0 Spare Parts Metal Set 1 Included: 4 x ARCL_S Nylon 12 x Oilless bushing (4x8x8) 6 x Bearing (3x9x5) 17 x Nut M3 x 0.5 6 x Spacer HexNut 4.75x6mm-M3 15 x Washer (3x7x0.5) 2 x Linear shaft D4x181mm 2 x Linear shaft D4x131mm 2 x Linear shaft D4x140mm 1 x M3 Thread rod for Z axis 1 x Z rod coupling

Visit The Website For More Information…